Armour Blog

Stall Divider Panel Layouts for a Growing Boarding Barn

Share
November 12th, 2026

A boarding barn that expects more horses in spring needs a divider plan before the first new stall is framed. Stall divider panel layouts for a growing boarding barn decide which horses share a wall, where staff can see into each stall, and which partitions stay put when the row gets longer. Start with the horses you already board, then compare stall divider packages for the run you expect to add.

Call Armour Horse Stalls at (386) 740-7459

This guide stays on that layout sequence. It does not replace a whole-barn workflow plan or a product comparison of every partition style. Use it when the aisle, posts, and next run of stalls are the decision in front of you.

What Should Stall Divider Panel Layouts for a Growing Boarding Barn Settle First?

Spring is when many barns add stalls because more horses are on the property. A layout that only fits today’s head count will force a rebuild once the new horses arrive. Write down three groups before you pick panels: horses that can see their neighbors, horses that need a quieter wall at feeding time, and stalls you may leave empty until the next phase.

Keep the current row and the future row on one sketch. Note which posts are already set and which posts the builder still has to place. A divider that lands on a shared post can stay in service while the next stall is added beside it. A divider that depends on a temporary end wall usually has to come out.

Match the panel family across the row

Armour Horse Stalls builds divider packages in two heights so a row can stay consistent. The Economy partition is the shorter package and pairs with an Economy stall front. The Bailey partition is the taller package and pairs with a Bailey stall front. The practical difference is height, not a change in how the grill is made.

Do not mix those heights on one shared run if you can avoid it. A shorter partition next to a taller one changes the sight line and the header line. Staff notice it every time they walk the aisle, and horses use the low spot. If one existing stall is already shorter, finish that run in the shorter family and start the new run as its own consistent row.

Both packages use a welded aluminum grill with round bars and separate vertical channels. You supply the posts and the lumber that fills the lower wall. That split is useful in a boarding barn. The grill stays a repeatable Armour component, and the lumber lets you match the barn you already have.

Write the height choice on the sketch before you price anything. A barn manager who orders the taller package for the new run and the shorter package for a repair on the old run will see the mismatch at the first shared post. Fix that on paper. Changing it after the grills ship means one run sits unused.

Also name who approves the layout. In a boarding barn that may be the manager, the owner, and the builder. If those three people are looking at different sketches, the posts move and the openings change. One marked drawing, with the occupied stalls hatched and the spring stalls numbered, keeps the order tied to the barn instead of to a guess.

How Should Divider Layouts Change as the Row Grows?

Think of the row in three stages. Stage one is the occupied stalls you will not move. Stage two is the empty bays you can frame now. Stage three is the wall or doorway you may open later. The divider layout should let stage one keep working while stage two is built.

Place open grill sections where familiar horses already live side by side and staff need a clear view from the aisle. Place a more closed lower wall where new boarders will meet horses they do not know, and at the stall where a horse eats. The grill can still sit above that lower wall so air and a limited view remain.

Leave the last divider in the current row able to become a shared wall. That means the end post should be a real stall post, not a wall cleat you plan to abandon. When the builder adds the next bay, that post is already the start of the new partition.

A simple sequence for spring

  1. Mark every stall that will still be occupied on the first day of the build.
  2. Choose one panel height for the whole new run and match it to the stall fronts on that run.
  3. Decide which shared walls stay more open and which get a solid lower section.
  4. Confirm the end post can carry the next divider without moving the current ones.
  5. Order the new partitions to the openings you measured, including any custom length.

If the barn may grow again after this spring, stop the row on a post you can build from. Do not finish the last bay against a wall you will need to remove. The facility expansion guide covers where to reserve that future space. This layout step only protects the partitions you are buying now.

Walk the row with the horses still in the stalls you will not rebuild. Note which shared walls the staff already treat as quiet and which ones they watch during grain. Those notes become the open-or-closed choice for the new bays. Copying one favorite stall down the whole run is how a barn ends up with too much contact in the stalls that needed less.

Give each new bay a job before you give it a panel. A stall beside the wash rack sees more traffic and more new horses. A stall at the quiet end of the aisle is a better home for a horse that startles. The divider layout should follow that job, not a single photo of a finished barn.

Which Horses Should Share an Open or Closed Wall?

Boarding barns rarely have one horse type in every stall. A quiet pair of school horses can share an open grill. A new arrival, a stallion, or a horse on restricted turnout usually needs less contact at head and chest height. Put that horse on a divider with a solid lower section and a grill above it, and keep the open grill for horses that already get along.

Feed time is the test. If two neighbors finish their grain without pinning ears through the bars, an open upper grill is doing its job. If one horse guards the wall, move the more closed layout to that shared side before you copy it down the row. You do not need every partition in the barn to match. You do need every partition in one run to use the same height and the same mounting plan.

Sick or incoming horses should not sit in the middle of the social row. Give that stall the more closed divider on both sides when you can, and keep it near a route staff already walk. The boarding barn stall guide covers the daily route. Use that route here only to decide which walls need more privacy.

Check the corners, not only the long walls. The first divider off the aisle post is the one horses meet when they are led in. If that corner is the busy one, do not put the most open grill there just because the rest of the row is open. Shift the more closed lower wall to the stall that sees the traffic.

When two new boarders will arrive in the same week, do not place them on a shared open grill on day one. Give them the more closed lower wall between them, and put familiar horses on their other sides. You can open the plan later if the pair settles. You cannot easily undo a bite through bars during the first week.

How Do Posts, Fronts, and Dividers Stay in Line?

A divider layout fails when the front system and the side wall assume different posts. On a multi-stall row, side-by-side stalls share the post at the corner. That post has to carry the stall front on the aisle and the divider that runs back from it. Measure the opening between the finished posts, not the center of the lumber you hope to use.

Armour divider packages include the grill and the receiver channels that hold the lower lumber. Grills longer than the standard shipping length arrive in two sections. Fasteners for a lumber barn are included. Fasteners for concrete are not, so a masonry wall needs its own anchor plan before you order. Special lengths are available. Call with the opening size rather than cutting a grill on site.

Match the divider family to the front on that same run. Review stall divider packages for the Economy and Bailey partitions, then check stall front packages so the aisle height agrees with the side walls. If you only need a grill for an opening you will frame yourself, look at stall partition grills. For a barn that already has posts and wants a panel between them, compare stall panels as a separate choice, not as a second layout in the same bay.

Layout choice. Use it when. Watch for this.
Open upper grill. Familiar horses share the wall. New horses may guard feed.
More closed lower wall. Use it for new boarders. Do not drop the grill height.
One height on the new run. Several stalls share posts. Mixed heights break the header line.
End on a real post. Another bay may come later. A temporary end wall gets removed.

What Should You Confirm Before Ordering the Next Run?

Order from the openings, not from a stall count. For each new bay, record the width between posts, the panel height you already chose, and whether the lower wall will be the more open or more closed version. Note which bays share a post with a stall that is already occupied so the installer does not plan to pull that post.

Ask the builder who supplies the posts and the lower lumber. The Armour package does not include either one. Also confirm the grill can ship in one piece or will arrive in two sections, and that someone on site can set both sections plumb before the lumber goes in. A two-section grill that is racked out of line will not meet the channels cleanly.

Armour Horse Stalls offers an array of standard and custom sizes, and custom sizes are available upon request. Bring the opening list to the call. The team can match Economy or Bailey partitions to those openings and flag a run that mixes heights or dead-ends on a wall you plan to remove.

Read the list back against the sketch one bay at a time. Occupied stalls stay off the order unless a shared post has to be reset. Empty bays get a width, a height, and a note about the lower wall. That is enough for a spring run. A longer wish list of future barns can wait until those openings are real.

Call (386) 740-7459 to review the next stall run

Frequently Asked Questions

Can I add stalls in spring without replacing dividers I already installed?

Yes, if the last post in the current row is a real shared post and the new run uses the same panel height. Build the next bay off that post. You should not have to remove the partitions that are already holding horses.

Should every new divider in a boarding barn be open?

No. Use an open upper grill where horses already get along and staff need to see in. Use a more closed lower wall where horses are new to each other or guard feed. Keep the height the same even when the lower wall changes.

Do Economy and Bailey divider packages work on the same row?

They can be ordered for different barns, but they are different heights. Keep one height on a shared run so the header and the sight line stay even. Match the divider to the stall front family on that same run.

What do I need to supply that the package does not include?

You supply the stall posts and the lumber for the lower wall. The package includes the welded grill, the channels that receive that lumber, and fasteners for a lumber barn. Concrete mounting needs its own anchors.

Where should a new or sick horse go in the layout?

Put that stall off the middle of the social row, with the more closed divider on the shared sides, and near a route staff already walk. Do not place it where every neighbor can reach through an open grill.

Toll-Free 800.876.7706
Fax 386.740.9077